For Installers

What is included in the printed form

This is a standard form that is sent to installers. It contains information such as:

  1. Order number and ceiling number

  2. Ceiling creation date

  3. Manufacturer/dealer data

  4. Client data

  5. Material that was used in this ceiling

  6. List with side lengths and diagonals.

  7. Direction of seams, if any

  8. Area and perimeter

  9. Installation profile

  10. Zero point.

    On this print form, you can select the zero point.

  11. Coordinates of points and fixtures

    See example

    On this print form, you can also enable and disable the display of coordinates of points and fixtures.

    Print example

To configure how the "For Installers" print form will look, we need to open the program settings and go to the "Print" tab. Open "Print Templates" and select the print form type "For Installers".

Now let's go through each setting in order.

  1. Print form type - here you select the print form for which the settings below will be applied. The dropdown list contains all print forms, both from the "Print" tab and from the "Calculation" tab.

  2. Barcode data - in this setting you can choose what data the barcode located on the print will contain.

    There are two data settings for barcodes:

    1. Order number

    2. Invoice barcode

  3. Display barcode - a setting that turns on and off the display of barcodes and QR codes on print forms.

    See example

    Setting enabled

    Setting disabled

  4. Display calculation table for installers - a setting that allows you to display on the print form a table from the "For Installers" calculation.

    See example

    Calculation For Installers

    Setting enabled

    Setting disabled

  5. Display Special notes - displays Special notes on the print form.

    See example

    Setting enabled

    Setting disabled

  6. Display order author - Displays on the print form the data of who created the order.

    For this setting, you must have authorization enabled in the program.

  7. Display dealer note - Displays on the print form a note that is specified in the dealer card.

    See example

    Dealer card

    Print form

    Setting disabled

  8. Title (printed in the upper right corner) - title for your print form that will be displayed in the upper right corner.

    See example

    Setting

    Print form

  9. Template (printed at the end of the sheet) - template where you can write any data and it will be displayed on the print form.

    See example

    Setting

    Print form

What questions does this article answer?

This article will help you find answers to the following questions:

  • How do I set up a printed form for installers in EasyCeiling?

  • What is included in the printed form "For installers"?

  • How do I set up a print form for the installation team?

  • How do I enable or disable barcodes on the form for installers?

  • How do I add a calculation table for installers to a printed form?

  • How can I put special marks on the form for installers?

  • How can I set up the display of the print order author for installers?

  • How do I add a dealer's note to a printed form for installers?

  • How can I change the name of the form for installers in the upper-right corner?

  • How do I add a template to the end of a printed sheet for installers?

  • What information does the form for installers contain?

  • How do I set up the display of QR codes on the forms for installers?

  • How can I print manufacturer's data on a printed form for installers?

  • How do I set up the display of the material on the form for installers?

  • How do I add a ceiling drawing to a printing plate for installers?

  • How can I display the area and perimeter on the form for installers?

  • How do I set up the seam direction display on the seal for installers?

  • How can I display the number of ceiling corners on the form for installers?

  • How can I add an error to the printing plate for installers?

  • How do I set up the barcode data for the installer's form?

  • How do I select the zero point on the printing plate for installers?

  • How can I enable or disable the display of coordinates of points and fixtures?

  • How do I set up a mounting profile on a printed form?

  • How can I display the coordinates of the fixtures on the form for installers?

  • How do I create a printed form for the installation team?